CVE-2026-99346HighMicrosoft CVSS 7.8CVSS:3.1/AV:L/AC:H/PR:L/UI:N/S:C/C:H/I:H/A:H/E:U

Microsoft security update for CVE-2026-99346 — azl3 kernel 6.6.161.1-1 on Azure Linux 3.0

Published
November 21, 2026
Last Modified
—

🔗 CVE IDs covered (1)

📋 Microsoft's advisory

EchelonGraph does not copy Microsoft's advisory page: its FAQ and remediation text are not shown here. Read the advisory on https://msrc.microsoft.com/update-guide/vulnerability/CVE-2026-99346. This page also shows what EchelonGraph holds for CVE-2026-99346, with the description from its CVE record, which the CVE Numbering Authority that assigned the CVE wrote: for a CVE Microsoft assigned, often in the words of Microsoft's own advisory.

🎯 Affected products1

  • azl3 kernel 6.6.161.1-1 on Azure Linux 3.0

✅ Updates Microsoft lists: 1 update

1 row: one per KB article or update, update type and fixed build. Their details are on Microsoft's advisory.

KB articleUpdateFixed build
—Security Update—

🧭 EchelonGraph on CVE-2026-99346

EchelonGraph score
8.8 HIGH
CISA KEV
Not listed
Fix status
A fix is available — apply it.

Description from the CVE record (CVE.org), as published by its numbering authority

In the Linux kernel, the following vulnerability has been resolved: KVM: SVM: Trigger new ASID allocation in both VMCBs on pCPU switch When the pCPU where the VMCB was most recently used is switched, reset the ASID generation in both VMCBs, triggering new ASID allocation for the immediate VMRUN as well as the next VMRUN on the other VMCB. The ASID is shared between vmcb01 and vmcb02, and gets flushed on every nested transition. However, since pCPU tracking is done per VMCB, it is possible for one VMCB to allocate a new ASID when migrated to a new pCPU, and then the other VMCB reuses that ASID on the old pCPU. This can result in the same ASID being used by multiple vCPUs on the old pCPU. Example scenario: - vCPU runs on pCPU A, vmcb01 is active, asid=1. - vCPU migrates to pCPU B, vmcb01 pCPU changes, new asid=2. - Another vCPU runs on pCPU A and allocates asid=2 as well. - vCPU migrates back to pCPU A, and then switches to vmcb02 before it runs again with vmcb01. - No pCPU switch is detected for vmcb02, so VMRUN is done with asid=2. - Two vCPUs end up using asid=2 on the same pCPU. Keep the VMCB dirtying to the active VMCB only. Clean bits are tracked by a pCPU for each VMCB, so do not unnecessarily dirty a VMCB if its pCPU does not change. Additionally, initialize the tracked pCPU for vmcb02 to -1 on nested enablement as hardening, so that a new ASID allocation is always triggered when nested is disabled and re-enabled. No performance regression was noticed when overcommitting L1 vCPUs in L0 (to force rescheduling), pinning L1 <-> L2 vCPUs, and running CPUID in a tight loop bouncing between 2 vCPUs in L2. An alternative (and perhaps more proper) fix would be tracking the ASID per-VMCB instead (e.g. [1]). However, that's a more involved change, and it would result in having different ASIDs for L1 and L2 without actually properly maintaining them. It would probably work because all TLB flushes target the current VMCB, and the other VMCB is always flushed on nested transitions, but the code ends up in an arguably more fragile state. Punt a proper clean fix to an incoming (and overdue) overhaul of SVM's ASID usage [2]. [1] https://lore.kernel.org/lkml/[email protected] [2] https://lore.kernel.org/kvm/[email protected]

Published by kernel.org, the CVE Numbering Authority that assigned CVE-2026-99346, in its CVE record at CVE.org; reused under the CVE Program's Terms of Use (its licence and MITRE's copyright notice are in our Terms of Service).

🔗 References (2)