In the Linux kernel, the following vulnerability has been resolved:
KVM: TDX: Enable Notify VM exit
Enable Notify VM exit functionality for TDX guests.
Notify VM exit is an existing feature supported by KVM. Userspace can
enable Notify VM exit through KVM_CAP_X86_NOTIFY_VMEXIT when it's
reported as supported. However, KVM reports the support of this CAP just
based on the hardware capability but doesn't differentiate between VMX
and TDX. This leads to the issue that userspace can enable this cap for
TDX guests without getting an error, but the feature is not actually
enabled because KVM doesn't call the TDX module API to program the
relevant TD VMCS fields.
Enable Notify VM exit for TDX guests by:
- Invoking TDX module API calls to set NOTIFY_VM_EXITING and Notify
Window in TD VMCS. It's done in tdx_vcpu_init() where other TD VMCS
bits are set. Since TDX vCPU cannot be reset, it only needs to be
configured once when initializing the TDX vCPU.
- Adding corresponding exit handler for TDX Notify VM Exit.
Notify VM exit can happen when executing the IRET instruction. If the
IRET unblocks the NMI blocking state, bit 12 of the exit qualification
is set. In this case, the VMM needs to restore the "blocked by NMI" state
when it decides to re-enter the guest. For TDX, KVM cannot manage the
GUEST_INTERRUPTIBILITY_INFO and it's TDX module's responsibility to
handle it. Extract the common part without NMI blocking handling into a
helper in common.h so that it can be shared between VMX and TDX.
Note, KVM uses "pre-production" terminology for the feature formally called
Notify VM-Exit. All public versions of the SDM refer to the feature as
Instruction Timeout. This will be remedied in the near future, for now,
use KVM's terminology for consistency.
Note, #2, there is no enumeration bit for Notify VM exit by TDX module
because all TDX modules support it, and allow to set the corresponding
TD VMCS fields as long as the hardware supports the feature.
What the EG score is made of (scorer v4.0: the three questions the 0–10 score mixes, published apart · methodology)
- EG Severity
- Not assessed: no CVSS publishedA missing CVSS is not a severity of zero.
- EG Likelihood
- 0.2% within 30 daysSource: FIRST EPSS. FIRST's exploitation probability, not an EchelonGraph model.
- Confirmed exploitation
- None on record (CISA KEV, EG-KEV Tier 1)Reported apart from the likelihood: an observed fact, not a probability.
- EG Priority
- No SSVC decision: EchelonGraph has not assessed this CVECISA BOD 26-04: 14 days if the affected system is publicly exposed; Fix on system upgrade if it is not.No released fix is confirmed on this page, but CISA's timeline does not wait for a fix's release: it starts when an agency identifies the flaw on an asset and updates the CDM Agency and Federal Dashboard, and the directive counts patching, decommissioning the system or another action as remediation. Until a fixed release is applied, mitigate as this page's verdict says. In the directive's words, “Fix on system upgrade” means that, “unless conditions change”, the vulnerability “should be remediated the next time the vulnerable asset receives a scheduled major upgrade or rebuild”: its timelines are “dynamic as facts change”, and a KEV listing shortens them.Each input and its source, and whom BOD 26-04 binds: the BOD 26-04 block below.
BOD 26-04 (CISA's remediation timeline, Table 1)14 days if the affected system is publicly exposed; Fix on system upgrade if it is not.
No released fix is confirmed on this page, but CISA's timeline does not wait for a fix's release: it starts when an agency identifies the flaw on an asset and updates the CDM Agency and Federal Dashboard, and the directive counts patching, decommissioning the system or another action as remediation. Until a fixed release is applied, mitigate as this page's verdict says. In the directive's words, “Fix on system upgrade” means that, “unless conditions change”, the vulnerability “should be remediated the next time the vulnerable asset receives a scheduled major upgrade or rebuild”: its timelines are “dynamic as facts change”, and a KEV listing shortens them.
The score's inputs: In CISA KEV no (CISA's KEV catalog) · Automatable no (CISA's BOD 26-04 default) · Technical impact total (CISA's BOD 26-04 default). Where an input reads “CISA's BOD 26-04 default”, no one has published it for this CVE, and CISA's implementation guidance says: “If “Automatable” and “Technical Impact” information items about a CVE ID are not available and the CVE ID is not in the KEV Catalog, CISA will treat its values as “no” and “total,” respectively, until CISA or a third party provides metadata about the CVE ID. CISA will always provide the Vulnrichment data for a CVE ID listed in the KEV Catalog.” Whether your system is publicly exposed is yours to answer. BOD 26-04 binds US Federal Civilian Executive Branch agencies; for anyone else it is CISA's published timeline, a reference rather than an obligation. The directive · how EchelonGraph applies it